ETA Lead-free reflow oven E8


Heating System
> Eight groups of top and bottom forced hot air convection heating zones.
> Patented heating plates in each zone uniformly transfer heat to the PCBs using forced hot air convection.
> Independent temperature control in each zone to ensure temperature uniformity within the process tunnel.
> Power consumption savings of 1/3 as compared to other systems.
> Patented motorized blower in each zone is designed to ensure stable air pressure, withstand high process temperature and is disturbance-free.
> Audible and light tower alarm for temperature limits, PCB drop, PCB jam and blower malfunction.
> Fast start-up (within 20 minutes) from room temperature to work temperature due to the high efficiency of the motorized heating plates.
Cooling System
> Two (2) groups of forced air convection cooling zones.
Distortion-free Conveyor System with Automated Chain Lubrication
> Combined pin chain rail and mesh belt conveyor system (Note: Mesh belt is not available on machines with center board support.)
> Closed-loop computer control of the conveyor provides a precise and repeatable reflow process.
> Automated chain lubrication system with a computer controlled central reservoir. Lubricant is added directly to the conveyor brush eliminating operator interface for this maintenance.
Fresh Air Recharge System
> Fresh air is supplied to each zone uniformly to provide a rapid process transfer.
Flux Management System
> Air amplifier forces supercharged flux collection and recirculation.
> Flux exhaust chimney with drawer shaped filter net is easy to access for maintenance.
Control System
> PC control system with windows based control software.
Additional Features
> Integrated UPS will be automatically activated in case of main power failure and will keep control PC and conveyor running for minimum 8 minutes to send out PCBs inside the oven tunnel.
> Motorized hood lift allows easy access to the inside of the oven for service and maintenance.
> Five (5) profiling ports and integrated profiling software are designed for convenient temperature profiling.
> Swing arm control PC station
> Four (4) emergency stop switches
> Two (2) exhaust ports
> SMEMA interface
> System documentation



Specifications : E8(8-Zone)
General
Outside Dimension(L*W*H) : 4800x1250x1490mm
Standard Color : Computer Grey
Weight : Approx.2250KG
Number Of Heating Zones : Up8/Bottom8
Length Of Heating Zones : 2900mm
Exhaust Volume : 10M3/minx2 Exhausts
Standard Feature Of Control System
Electric Supply Required : 3phase, 380V 50/60Hz
Power For Warm Up 30KW
Power Consumption 8KW
Warming Time : Approx.20 minute
Temp. Setting Range : Room Temp. --- 300℃
Temperature Control Method : PID Close Loop Control + SSR Driving
Temperature Control Precision : ± 1.0℃
Temperature Deviation on PCB : ± 1.5℃ (by MR Board Test Standard)
Heating Element : Especial Heating elements For Long Life ;
Commutated Element : Aluminium Alloy Plate
Max. Temp. Gap Between Preheat & Reflow Setting : 80℃
Max. Temp. Gap Between Preheat Zones Setting : 40℃
Max. Temp. Gap Between Reflow Zones Setting : 50℃
Data Storage : Process Data and Status Storage
Abnormal Alarm : Abnormal Temperature (Extra-high / Extra-low Temp.)
Board Dropped Alarm : Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal
Features Of Conveyor System
Rail Number : 1 Lane
Max.Width Of PCB : 320mm (Option:610mm )
Components Clearance : Top/ Bottom Clearance of PCB is 25mm
Converyor Direction : L→R (Option: R→L)
Fixed Rail Side : Front Rail Fixed(Option:Rear Rail Fixed)
Transmission Agent : Air-Reflow = Chain + Mesh , N2-Reflow=Chain(Mesh is option)
Center Support (Option) : Preventing PCB warp such too wide and heavy component load
Converyor Height : 900+/-20mm
Converyor Speed Range : 300～2000mm/min
Lubrication Auto-Afflux : Standard
Temp. Thermocouple Slot : Standard
Driven Top Hood Opening : Standard
On Line Editing : Standard
Cooling Method : Forced-Air (Standard), Water-Chiller (Option)
Model for Nitrogen Process
Power For Warm : Up 32KW
Power Consumption : 12KW
Flux Management System : Flux Reclaimed and Filtration standard for N2Oven, easy clean-up.
N2 containment at Entry and Exit End Standard
Flux Reclaim System : Standard
Nitrogen Flow Meter : Standard
Oxygen Analyser : Option
Nitrogen Consumption [Standard] : 400~1000PPM 20M3/H
Water Chiller : 3 HP ; External Stand-alone Type ; Powerful Cooling suit to Lead-Free Process Required

ETA Electronic equipment CO., LTD. to provide professional SMT automatic production line solution, The company specializes in SMT chip mounter(New samsung:SM421, SM411, SM100 etc)(second-hand： CP40L; CP40LV; CP45F; CP45FV; CP45FVneo); YAMAHA SMT machine (YAMAHA Chip shooter); JUKI chip mounter , SIEMENS SMT machine , PANASONIC SMT Chip mounter, FUJI second-hand SMT machine.We are also sell printing machine, Point glue machine, Reflow soldering, Wave soldering, Automatic plug-in machines, SAMSUNG SMT machine feida ，Accessories , stencil printer, Reflow oven, flow welding, Panasert, AOI, X-ray, LED automatic die bonder etc, For communication products manufacturers, LED display, lighting manufacturers; SMT, AI materials processing, and other enterprises provide the required equipment or wiring scheme.


Main new
SAMSUNG chip mounter:SM421S, SM421, SM411, SM431, SLM100, SLM120, SM471, SM481 etc.
YAMAHA SMT machine:YS12, YS24, YS100, YG12, YG100RA, YV100X.
SIEMENS SMT shooter:D4, D2, D1, S20 25 27 50 60 , F3, F4, F5
PANASONIC SMT equipment:CM402, CM602, NPM.
JUKI Chip shooter:KE2070, KE2080, KE2060, KE2050.
FUJI SMT mounter:CP6, CP642, CP643, CP742, CP842, XP241, QP341, QP242, IP3, IP2.
SANYO Automatic Mounter:TCM3000Z, TCM-X200.
I PULSE FV5530, 7100.M1, M2, M3, M4
MIRAE MPS1010, MX100, MX200
NEW automatic plug-in machines, horizontal plug, Vertical plug, Bulk LED plug, Reflow oven, wave soldering, domestic, import have lead, lead-free reflow soldering; Wave soldering,
Other SMT related equipment:: AOI; X - ray testing equipment t; Semi-automatic and fully automatic printing machine.